Vinyl Tubing for C-530

PR11510
Product No. PR11510

$18.00

Buy Now Find a Store In Stock
Vinyl Tubing for C-530.
Vinyl Tubing for C-530 is rated 4.7 out of 5 by 7.
Rated 5 out of 5 by from Aquarium Tubing Tubing worked great to hook up our filters that previous person could not get to work.
Date published: 2017-01-10
Rated 3 out of 5 by from BEWARE - THIS IS ONLY ONE HOSE, NOT BOTH!! I was under the impression that this would be a replacement for both hoses. It is just one length of hose. Product should be labeled better!
Date published: 2016-12-16
Rated 5 out of 5 by from IF you clean them they last years! Here how... I bought a flexible sink drain cleaning brush that fits inside this tub and cleans the inside after only a few passes. If your tub is long you will have to run the brush from both ends. I do this 1 to 2 times a year and the filter runs like new after it!
Date published: 2015-12-28
Rated 5 out of 5 by from vinyl tubing. Easy to use and doesn't leak. Doesn't kink and easy to clean
Date published: 2015-12-21
Rated 5 out of 5 by from New clean hoses work great! New clean hoses work great and old hoses were discarded. I get the full water pressure from the C-530 Canister filter now and it runs like new!
Date published: 2014-09-25
Rated 5 out of 5 by from Tubing replacement Needed a new hose the other one was not long enough. Item was as described with quick delivery.
Date published: 2014-07-12
Rated 5 out of 5 by from works for intended function, needs to be replaced or cleaned every few years due to waste collection along the inner walls of the tubbing works like it should! I have never had a problem!!
Date published: 2013-07-02
  • y_2018, m_4, d_22, h_23
  • bvseo_bulk, prod_bvrr, vn_bulk_2.0.8
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_7
  • loc_en_US, sid_PR11510, prod, sort_[SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_marineland

What is the ID dimension of this C-530 hose?

Asked by: RogerU
It is 1". BREX
Answered by: BREX
Date published: 2018-02-07

will this tubing fit a magnum 350

Asked by: rocko
Hi rocko, No, it sure won't. You need tubing that is 5/8" ID, and this is 1" ID. You can buy tubing at your local DIY hardware store or the C160/220 tubing will work. BREX
Answered by: BREX
Date published: 2018-02-07

does the order come with two 5 ft hose

Asked by: nico
It is one length of tubing, not two. BREX
Answered by: BREX
Date published: 2018-02-07

Dumb question: but on a marine land c530! The in take tube! When you tight the hose behind the tank at the top of the tank which way do you go! I still see bubbles !  I think I'm Going the wrong way! Any pictures of what it looks like fully tightened ? 

Asked by: Josh24
The intake tube takes a c clamp. You don't tighten this in any direction per se, you close it as tight as it will go, by squeezing it. It is normal to see bubbles for the first 2-3 days while the filter purges air; this will go away. If it does not go away, you may not have put the tubing onto the valve block correctly. Make sure you have the barbs completely covered, and the tubing should also cover the threads after the barbs. BREX
Answered by: BREX
Date published: 2016-12-14

It seems if I leave the tube full length l get bubbles?  But if I do a slight kink in tube it takes the bubbles away? Should I just cut tube and make it smaller? I don't want all these bubbles it makes tank look bad!  Is it bad to leave the kink? 

Asked by: Josh24
Thank you for your question! Excess bubbles can occur for a number of reasons, so check the following to make sure everything is correct: - c clamp on the intake tube may need to be tighten a little bit - tubing should push over the barb AND over the threads on the valve block, otherwise, there is a gap that will constantly pull in air. - if the filter is brand new, the filter may be purging air, and this can take 1-3 days to complete, depending on how it was set up, etc. In regards to the tubing, you should only have a 2" slack in it. If the tubing loops below the motorhead, you definitely want to cut some excess off of it, as this could be your issue. No, do not leave it kinked - this can cause an issue down the road. BREX
Answered by: BREX
Date published: 2016-12-01

Is this for both the input and output tubes or do i need to buy two of them?

Asked by: Thatoneguy
You would receive two separate lengths, one for the intake and one for the output. BREX
Answered by: BREX
Date published: 2016-06-22

What is the best or efficient way to clean tubes?

Asked by: Rock70
For vinyl tubing, you can curl in up and place in a bucket of vinegar solution for an hour or so, or you can use a wire with a rag attached to pull it through. Soak the rag in vinegar. BREX
Answered by: BREX
Date published: 2015-05-26

C-530 Vinyl tubing size

I know the tubing is 1 inch, however is that 1 inch actual inside diameter or 1 inch actual outside diameter?
Asked by: Firemedic133
The tubing for the C-530 is a 1 inch ID (internal diameter.) The tubing thickness is approximately 1/8 of an inch thus making the OD (outer diameter) right around 1 1/4". ML2
Answered by: BREX
Date published: 2018-03-09
  • y_2018, m_4, d_22, h_23CST
  • bvseo_bulk, prod_bvqa, vn_bulk_2.0.8
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_10
  • loc_en_US, sid_PR11510, prod, sort_[SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_marineland